Adtran 904 PRI Config

Adtran 904 PRI Config

*****REQUIRED*****

Serial Connection for console access to the device

 

*****INSTRUCTIONS*****
The config template provided below will setup a registration based SIP Trunk on an ADTRAN 904 with a PRI out. It does not include any of the networking settings which are unique to each installation.

Before using this template you must find and replace the following values:

123USER with your Account Number (The SIP Username).
456PASS with your Service Password.

Note that when quotations ("") exist must remain in use. For example "13055551212" and "1secret2"

*****START YOUR COPY BELOW THIS LINE*****

 

 

interface eth0/1
media-gateway ip primary
interface t1 0/1
tdm-group 1 timeslots 1-24 speed 64
no shutdown
!
interface pri 1
description pri 1
isdn name-delivery proceeding
connect t1 0/1 tdm-group 1
role network b-channel-restarts enable
no shutdown
!
isdn-group 1
connect pri 1
!
ip sip
ip sip udp 5060
no ip sip tcp
!
voice feature-mode network
voice forward-mode network
!
voice spre 1 *XX&
!
voice dial-plan 1 local NXX-NXX-XXXX
!
voice trunk T01 type sip
description "SIPIN"
sip-server primary sbc.ringlogix.com
registrar primary sbc.ringlogix.com
authentication username "123USER" password "456PASS"
max-number-calls 23
register 123USER
!
voice trunk T02 type isdn
description "PRIOUT"
resource-selection linear descending
connect isdn-group 1
rtp delay-mode adaptive
!
voice grouped-trunk DIALPLAN
trunk T01
trunk T02
accept NXX-NXX-XXXX cost 0
accept 1-NXX-NXX-XXXX cost 0
accept 1-800-NXX-XXXX cost 0
accept 1-888-NXX-XXXX cost 0
accept 1-877-NXX-XXXX cost 0
accept 1-866-NXX-XXXX cost 0
accept 1-855-NXX-XXXX cost 0
accept 011-$ cost 0
accept 411 cost 0
accept 611 cost 0
accept 911 cost 0
accept 0-NXX-NXX-XXXX cost 0
accept 10-10-XXX-$ cost 0
accept $ cost 0
reject NXX-976-XXXX
reject 1-900-NXX-XXXX
reject 1-976-NXX-XXXX

!
ip sip qos dscp 46
!
ip rtp udp 15000
!

 

    • Related Articles

    • IPitomy Configuration Guide

      Trunk Config Settings for IPitomy PBX

    • Grandstream UCM61XX Configuration Guide

      To log into the PBX, use the IP address found on the LED screen of the UCM. Use a web browser and go to that address. Since the web GUI is using https, it will warn you that the "site's security certificate is not trusted" or you will see an SSL ...

    • Add New SIP Trunk

      Our white label SIP Trunk solution is compatible with any SIP enabled device. This includes IP PBX systems and FXS or PRI Gateways that convert SIP signaling to traditional handoffs used by legacy PBX and key systems. Add a SIP Trunk Add or Search ...

    • Cisco SPA8000 Configuration Guide

      Find the IP address of the Cisco SPA8000. Connect an analog phone to the first FXS port. From the analog phone dial **** (four asterisks). Then press 110# to determine the IP address (the system will speak the address, EXAMPLE: 192.168.1.130). Once ...

    • 3CX Configuration Guide

      RingLogix is proud to be part of a select group of Providers that have been officially tested and certified by 3CX. Note: Before trying to configure your 3CX phone system please make sure you have already created a customer and activated a SIP Trunk ...