T.38 Fax Overview

T.38 Fax Overview

How Does T38 Faxing Work?

Fax machines on the PSTN communicate using the T30 protocol. T38 encapsulates the T30 transmission in real-time and uses data redundancy methods to ensure the complete delivery of a fax. By sending the same packets up to 5 times, most issues with jitter and packet loss on the last mile do not affect the fax completion rate.

 

Is T38 Faxing Reliable?

In short, YES. Infact we send 40-60 page faxes with it all the time. Even, non T38, 711 fax pass-though transmissions work very well.

However, for most people, their prior experiences are usually not the same as ours and it's for for a couple reasons; bad carrier implementations, bad services and or bad hardware.

Infact, most T38 and 711 fax pass-through failures are blamed on poor last mile internet connections with jitter, latency and packet loss as the usual suspects. However, FoIP failures are much more commonly related to 2 other issues known as ‘late-arriving T.38 re-Invites’ and ‘PCM Clock Sync’ problems.

Late-arriving T.38 re-Invites sent after a fax transmission has already begun will cause the fax to drop; and PCM clock sync mismatches, found on 711 pass-through transmissions, steadily grow per fax page also causing the fax to drop. Both problems result in the all too common complaint of “1-2 page faxes work fine but big faxes fail”.

To address these problems, RingLogix  has partnered with Netgen, a manufacture of Fax Aware analog telephone adapters (ATA). Netgen has developed a patented solution to address the ‘late-arriving T.38 re-Invites’ and ‘PCM Clock Sync’ problems mentioned. 

To resolve the first issue the ATA monitors the line and listens for fax transmissions. If a fax is already in progress and a late-arriving T.38 re-Invite is received, the ATA will reject it and continue the transmission in 711 pass-through mode. To address the PCM clock sync mismatch that occurs on larger faxes, the ATA will re-sync the PCM timer’s in-between each page, essentially treating a multi-page fax as several single page faxes. This is done without delaying the original transmission.

 

How to purchase Fax-Aware ATA's

From Netgen Directly:


Recommended Models - Configurations:
  • HX402E - 2 FXS Ports
  • HX404E - 4 FXS Ports
  • HX402G - 4 FXS Ports
  • HX404G - 4 FXS Ports

Click here for a configuration guide.

 

    • Related Articles

    • T38 Fax Trunk Settings

      The RingLogix T38 IP Fax solution is compatible with all customer premise equipment, both SIP enabled and analog based. However, we ONLY recommend the use of the Netgen Fax ATA described in our T.38 Fax Overview article. While no IP Fax service or ...

    • Add New IP Fax - T38 Fax Trunk

      Currently, RingLogix offers 2 IP Fax service. This includes T38 based faxing with our custom Fax-Aware Adapter and an Inbound Fax to Email solution. Add a T38 Fax Trunk Add or Search for an existing customer. To search for a customer type any ...

    • Add New IP Fax - Fax 2 Email Service

      Currently, RingLogix offers 2 IP Fax service. This includes T38 based faxing with our custom Fax-Aware Adapter and an Inbound Fax to Email solution. Add a Fax 2 Email Service Add or Search for an existing customer. To search for a customer type any ...

    • Netgen HX422 Fax ATA Configuration Guide

      This article will show you how to configure the Netgen Fax ATA for use on the RingLogix T38 IP Fax platform. Netgen HX422 Configuration Guide 1. Power on the device and connect the PC port to your internet switch or router. 2. The device will ...

    • Introducing WebFax by RingLogix

      What is WebFax? WebFax by RingLogix is an advanced and flexible internet fax solution that allows users to send and receive faxes using their email, web portal, or traditional fax machines with the help of a Fax ATA (Analogue Telephone Adapter). ...